Moose Troubleshooting
Moose Z1100E Alpha keypad
Arm
Press [LEAVE] or [STAY]. Then enter your CODE. If you selected [STAY], the keypad will ask you to confirm the interior and delay setting. Press [CONFIRM].
Disarm
Press [DISARM] and enter CODE.
Check Faulted Zones
If keypad says [ZONE(S) NOT READY], press [DISPLAY] to view faulted zones.
Smoke Reset
First, enter CODE to silence alarm. If a smoke detector is latched in alarm, the keypad will say [SUPERVISORY/TROUBLE]. You can press the scroll key to verify the trouble condition(s). Press [SMOKE RESET] and then your CODE.
Code Change
Press Menu Scroll Key 3 times. Press [PROGRAM]. Enter Master Programming Code. Press [CONTROL PANEL]. Press Function Number (01 for user code 1 — thru — 17 for user code 17). Press [FIND] when prompted. Display will show first digit of this users code. Enter each digit of desired new code. Codes must be 5 digits in length. If you want a shorter code, use trailing zeros (i.e. code 555 would be entered 55500.)
Chime Mode On/Off
Press Menu Scroll Key twice. Press [DAY MONITOR]. Enter CODE.
Force Arm Over Bad Zones
If enabled, keypad will give [LEAVE] and [STAY] options when displaying [ZONE(S) NOT READY]. Press [LEAVE] or [STAY]. Either [BYPASS] or [OVERRIDE] will display. Select this option. If more than one zone is faulted, scroll through faulted zones and bypass or override.
The system is going off and I do not have a code to turn it off?
My alarm is going off and I can’t get it to turn off.
- Go to the security system panel box usually found in the basement or closet. Open the panel box & locate the battery.
- Unplug the security system power supply transformer.
- Then disconnect or pull off one of the wires that is attached to the battery in the alarm control box.
- This will power down the security system. Once you have done this, contact us 919-460-5995 to schedule service.
Moose Z1100 Panel LED Keypad
Arm
Press [1] plus code.
Disarm
Press [1] plus code.
Check Faulted Zones
Lift cover on keypad. Press [2], then your code. For 8 seconds, lights become zone display lights.
Change code
Press [9] + Master Programming Code. Panel will beep twice, all lights will blink, [Press # corresponding to user number you want to add/change], Panel will beep 3 times, [Enter 5 digit new code], (shorter code can be entered by putting zeros after code) after 5th digit panel will beep one long beep.
The system is going off and I do not have a code to turn it off?
My alarm is going off and I can’t get it to turn off.
- Go to the security system panel box usually found in the basement or closet. Open the panel box & locate the battery.
- Unplug the security system power supply transformer.
- Then disconnect or pull off one of the wires that is attached to the battery in the alarm control box.
- This will power down the security system. Once you have done this, contact us to schedule service.
Moose ZX400 KEYPAD
CLEAR Quit Key
Used to reset any entry error and to allow you to exit out of an operation.
Medical
(Auxiliary)
Fire Police
(Hold Up)
Panic Keys
When enabled, these keys activate the auxiliary alarms (Fire, Police, Medical) or call your pager. Consult with your Security Company Representative for details.
NIGHT
Bedtime; selected door, window and interior sensors are ON
STAY
Building is occupied; selected door & window sensors & ON.
AWAY
No one at home; total protection; all sensors are ON.
Armed Status Indicator
These keys, followed by your passcode, are used to turn your system ON. Each key corresponds to a different level of security.
OFF CANCEL Off Cancel Key
Used to turn OFF, silence, or cancel conditions.
ENTER KEY Instant Key
Used in programming to store entered data. May also be used to disable the entry and exit countdown time when pressed during the countdown time when turning the system ON with STAY or NIGHT.
1 View Info Key
This key is used to view system information.
0 Access Key
Used to activate a door strike or other access output function.
9 Program Key
Used to enter the programming mode.
8 Test Key
Allows you to perform system testing.
7 Reset Smoke Key
Resets all smoke detectors in alarm.
6 Chime Key
Turns the door/window monitor ON or OFF.
5 Delay Arm Key – (ZX400/ZX410/ZX440F only)
Extends or postpones the Automatic-ON by one hour.
4 Bypass Key
Allows you to turn your system ON with one or more zones intentionally left unprotected until the system is turned OFF.
3 Event Log Key – (ZX400/ZX410/ZX440F only)
Allows you to view events on the keypad. If a printer is attached, you may print the recorded activities.
2 Alarm Memory Key
Allows you to display the most recent zones where an alarm occurred.